Tweco Torch Data for Auto-Cut O2 V.2 Manual do Utilizador descarregar pdf (Página 27)

Manual 0-4832 Rev AF 8-27 TORCH DATA for AutoCut O

(ga) (in) inch (PSI) (Ball) (PSI) (Ball) (PSI) Volts

(in)

±0.005

(ipm) (in) (sec) (in)

3/8 0.375 20 80 90 5 55 155 0.160 95 0.300 0.0 0.110

1/2 0.500 20 80 90 5 55 156 0.160 85 0.300 0.4 0.115

5/8 0.625 20 80 90 5 55 158 0.180 65 0.300 0.5 0.122

3/4 0.750 20 80 90 5 55 163 0.200 50 0.300 0.7 0.133

7/8 0.875 20 80 90 5 55 177 0.250 40 0.400 0.9 0.149

1 1.000 20 80 90 5 55 183 0.300 35 0.450 1.0 0.148

1 1/4 1.250 20 80 90 5 55 185 0.300 20 0.176

1 1/2 1.500 20 80 90 5 55 200 0.350 10 0.211

1 3/4 1.750 20 80 90 5 55 207 0.350 8 0.216

(Bar) (Ball) (Bar) (Ball) (Bar) Volts

(mm)

±0.1

(mm/min)

(mm) (sec) (mm)

1.4 80 6.3 5 3.8 155 4.1 2400 7.6 0.0 2.8

1.4 80 6.3 5 3.8 156 4.1 2000 7.6 0.4 2.9

1.4 80 6.3 5 3.8 157 4.4 1550 7.6 0.5 3.1

1.4 80 6.3 5 3.8 165 5.1 1100 7.6 0.7 3.4

1.4 80 6.3 5 3.8 183 7.6 900 11.4 0.9 3.7

1.4 80 6.3 5 3.8 185 7.6 500 4.5

1.4 80 6.3 5 3.8 200 8.9 250 5.4

1.4 80 6.3 5 3.8 206 8.9 200 5.5

Stainless Steel

200A

Plasma / H

O Shield

BOLD TYPE

indicates maximum piercing parameters.

BOLD ITALIC

indicates edge starts only.

Requires CCM version 3.4 or later. Requires GCM version 3.2 or later.

Edge Start

38 Edge Start

Edge Start

Kerf Width

@ Rec.

Speed

Plasma (N

)

Shield

O)*

(mm)

Edge Start

Material

Thickness

Pre Flow

Pressure

)

Cut Flow Rates /

Pressures Arc

Voltage

Torch

Working

Height

Travel

Speed

Initial

Piercing

Height

Pierce

Delay

Kerf Width

@ Rec.

SpeedPlasma (N

)

Shield

O)*

Edge Start

Torch

Working

Height

Travel

Speed

Initial

Piercing

Height

Pierce

Delay

Material

Thickness

Pre Flow

Pressure

)

Cut Flow Rates /

Pressures Arc

Voltage

36-1048 36-1089 36-102036-1016 36-1039 36-1273 36-1064

* Pressure of the water supply line should be regulated by customer pressure regulator.

Note1:

Ohmic height sensing is not recommended with water shield. Water on the plate interferes electrically with the

ohmic sensing circuit.

Note2:

Water source used for shield must be demineralized.

Plasma Gas

Distributor

Electrode CartridgeShield Cup Shield Cap

Shield Gas

Distributor

Tip

Electrode

Shield Cap

Tip

Shield Gas

Distributor

Plasma Gas

Distributor

Cartridge

Shield Cup

This Art Is For Reference ONLY

Art # A-07958_AB

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 53 54

Comentários a estes Manuais

Sem comentários

Tweco Torch Data for Auto-Cut O2 V.2 Manual do Utilizador Página 27

Comentários a estes Manuais

Manuais e produtos relacionados com Hardware Tweco Torch Data for Auto-Cut O2 V.2