Tweco Torch Data AutoCut Manual do Utilizador descarregar pdf

Manual 0-4825 Rev. AK 8-1 TORCH DATA for AutoCut Basic

8. TORCH OPERATION

Torch Parts Selection

The application will determine which torch parts must be used. Refer to the cut charts for the proper torch parts to

install for a selected application.

Do not interchange parts. Make sure all torch parts correspond with the

plasma and shield gases in use for the application.

Pre-Setting Power Supply Controls

Set the Power Supply controls prior to operating the system as described in the power supply Operating Manual.

Refer to the cutting charts for the proper cutting parameters for the application.

Recommended Cutting Speeds

Cutting speed depends on material and thickness. The following factors may affect system performance:

• Torch parts wear; gas quality and mass flow / pressure; operator experience; torch standoff height; proper

work cable connection; alloying contents of material; cutting table capabilities & accuracy.

This information represents realistic expectations using recommended

practices and well-maintained systems. Actual speeds may vary from

those shown in the charts depending on the alloy content of the selected

material. Voltage ratings may vary depending on the CNC, cutting table,

or height controller.

For complete cutting speed chart data refer to the following pages.

Consumables Notes

Always assemble the consumable parts properly. Improper assembly may damage the parts or the torch head.

Ensure that parts are seated together correctly.

Always check the shield gas distributor for charring when changing parts. Do not use the distributor if it is charred.

Replace the shield gas distributor regularly to ensure proper performance.

Operational Notes

Always purge the torch after changing consumables or if the power supply has been shut off. The power supply's

built-in purge function may not be enough to properly purge the torch. Manually flow gas with the 'Test Cut Flow' and

'Test Pre-Flow' functions to help remove any remaining coolant from the lines.

Slightly increasing the preflow pressure may increase piercing ability on thicker materials. However, increasing the

preflow pressure too much may affect plasma starting reliability (misfiring).

Decreasing preflow pressure may improve piloting. Preflow pressure can be reduced without affecting cut perfor-

mance as long as the pilot arc still transfers to the plate well. Decreasing preflow pressure too much will affect the

ability to transfer the arc to the plate and may cause damage to the tip.

Notes on Chart Measurements

Pressure measurements in the charts are in psi(g), not psi(a). 0 psi(g) = 14.7 psi(a) (1 atmosphere).

Ball settings are at the center of the gauge ball.

1 2 3 4 5 6 ... 43 44

Resumo do Conteúdo

Página 1 - 8. TORCH OPERATION

Manual 0-4825 Rev. AK 8-1 TORCH DATA for AutoCut Basic8. TORCH OPERATIONTorch Parts SelectionThe application will determine which torch parts must

Página 2 - Underwater Cutting

TORCH DATA for AutoCut Basic 8-12 Manual 0-4825 Rev. AKStainless Steel100AH35 Plasma / N2 ShieldPlasma (H35) Shield (N2) (ga) (in) inch (PSI) (PSI)

Página 3 - Air Plasma / Air Shield

Manual 0-4825 Rev. AK 8-13 TORCH DATA for AutoCut BasicStainless Steel100AN2 Plasma / H2O ShieldPlasma (N2) Shield (H2O) (ga) (in) inch (PSI) Ball *

Página 4

TORCH DATA for AutoCut Basic 8-14 Manual 0-4825 Rev. AKAluminum100AAir Plasma / Air ShieldPlasma (Air) Shield (Air) (ga) (in) inch (PSI) (PSI) Volt

Página 5

Manual 0-4825 Rev. AK 8-15 TORCH DATA for AutoCut BasicAluminum100AH35 Plasma / N2 ShieldTip35-1062Electrode35-1080PlasmaGas Distributor35-1041Art #

Página 6

TORCH DATA for AutoCut Basic 8-16 Manual 0-4825 Rev. AKAluminum100AN2 Plasma / H2O ShieldCartridge35-1020Shield Cup35-1016Shield Cap35-1034Shield Gas

Página 7

Manual 0-4825 Rev. AK 8-17 TORCH DATA for AutoCut BasicPlasma (H35) Shield (N2) (ga) (in) inch (PSI) (PSI) Volts(in)±0.005(ipm)(in)(sec)(in)3/8 0.3

Página 8

TORCH DATA for AutoCut Basic 8-18 Manual 0-4825 Rev. AKThis Page Intentionally Blank

Página 9 - Art # A-04863

Manual 0-4825 Rev. AK 8-19 TORCH DATA for AutoCut BasicMaterial Gases UsedConsumable Description100A 55AElectrode35-1071 35-1069Plasma Gas Distributo

Página 10 - Art # A-04938

TORCH DATA for AutoCut Basic 8-20 Manual 0-4825 Rev. AKThis Page Intentionally Blank

Página 11 - Electrode

Manual 0-4825 Rev. AK 8-23 TORCH DATA for AutoCut BasicMild Steel200AAir Plasma / Air ShieldPlasma (Air) Shield (Air) (ga) (in) inch (PSI) (PSI) Volt

Página 12 - Air Plasma / Air Shield

TORCH DATA for AutoCut Basic 8-2 Manual 0-4825 Rev. AKOhmic SensingOhmic sensing is not recommended with water shield. Water on the plate interferes

Página 13

TORCH DATA for AutoCut Basic 8-24 Manual 0-4825 Rev. AKMild Steel200AO2 Plasma / Air ShieldElectrode35-1085Shield Cap35-1029Shield Retainer35-1019Tip

Página 14 - O Shield

Manual 0-4825 Rev. AK 8-25 TORCH DATA for AutoCut BasicStainless Steel200AAir Plasma / Air ShieldPlasma (Air) Shield (Air) (ga) (in) inch (PSI) (PSI)

Página 15

TORCH DATA for AutoCut Basic 8-26 Manual 0-4825 Rev. AKStainless Steel200AH35 Plasma / N2 Shield **Plasma (H35) Shield (N2) (ga) (in) inch (PSI) (P

Página 16 - This Page Intentionally Blank

Manual 0-4825 Rev. AK 8-27 TORCH DATA for AutoCut BasicShield CapShield Gas DistributorTip35-1039 35-1273 35-1064Plasma (N2) Shield (H2O)*(ga) (in) i

Página 17 - Auto-Cut Basic

TORCH DATA for AutoCut Basic 8-28 Manual 0-4825 Rev. AKAluminum200AAir Plasma / Air ShieldPlasma (Air) Shield (Air) (ga) (in) inch (PSI) (PSI) Volts(

Página 18

Manual 0-4825 Rev. AK 8-29 TORCH DATA for AutoCut BasicAluminum200AH35 Plasma / N2 Shield **Plasma (H35) Shield (N2) (ga) (in) inch (PSI) (PSI) Vol

Página 19 - Mild Steel

TORCH DATA for AutoCut Basic 8-30 Manual 0-4825 Rev. AKElectrodeShield CapTipShield Gas DistributorPlasma GasDistributorCartridgeShield CupThis Art I

Página 20 - Plasma / Air Shield

Manual 0-4825 Rev. AK 8-31 TORCH DATA for AutoCut BasicShield CapShield Gas Di st ri but orTipPlasma (N2) Shield (H2O)*(ga) (in) inch (PSI) (Ball) Vo

Página 21 - Stainless Steel

TORCH DATA for AutoCut Basic 8-32 Manual 0-4825 Rev. AKThis Page Intentionally Blank

Página 22 - Shield **

Manual 0-4825 Rev. AK 8-33 TORCH DATA for AutoCut BasicMaterial Gases UsedConsumable Description200A 100A 55AElectrode35-1085 35-1071 35-1069Plasma

Página 23

Manual 0-4825 Rev. AK 8-5 TORCH DATA for AutoCut BasicMild Steel55AAir Plasma / Air ShieldPlasma (Air) Shield (Air) (ga) (in) inch (PSI) (PSI) Vol

Página 24 - Art # A-07594

TORCH DATA for AutoCut Basic 8-34 Manual 0-4825 Rev. AKThis Page Intentionally Blank

Página 25

Manual 0-4825 Rev. AK 8-37 TORCH DATA for AutoCut BasicMild Steel300AAir Plasma / Air Shield Shield CapShield Gas DistributorTip35-1037 35-1283 35-10

Página 26

TORCH DATA for AutoCut Basic 8-38 Manual 0-4825 Rev. AKStainless Steel300AAir Plasma / Air Shield Shield CapShield Gas DistributorTip35-1037 35-1283

Página 27 - Make Copies as Desired

Manual 0-4825 Rev. AK 8-39 TORCH DATA for AutoCut BasicAluminum300AAir Plasma / Air Shield Shield CapShield Gas DistributorTip35-1037 35-1283 35-1050

Página 28

TORCH DATA for AutoCut Basic 8-40 Manual 0-4825 Rev. AKThis Page Intentionally Blank

Página 29

Manual 0-4825 Rev. AK 8-41 TORCH DATA for AutoCut BasicShield CapShield Gas DistributorTip35-1037 35-1283 35-1050Plasma (Air) Shield (Air) (ga) (in)

Página 30

TORCH DATA for AutoCut Basic 8-42 Manual 0-4825 Rev. AKThis Page Intentionally Blank

Página 31

Manual 0-4825 Rev. AK 8-43 TORCH DATA for AutoCut BasicMaterial Gases UsedConsumable Description300A 200A 100A 55AElectrode35-1088 Air/Air35-1085 3

Página 32

TORCH DATA for AutoCut Basic 8-44 Manual 0-4825 Rev. AKThis Page Intentionally Blank

Página 33

Manual 0-4825 Rev. AK 8-47 TORCH DATA for AutoCut BasicTORCH REPLACEMENT PARTSReturnsIf a product must be returned for service, contact your authoriz

Página 34

TORCH DATA for AutoCut Basic 8-6 Manual 0-4825 Rev. AKMild Steel,55AO2 Plasma / Air ShieldTip35-1272Electrode35-1025Shield Cap35-105135-104135-1069Ca

Página 35

TORCH DATA for AutoCut Basic 8-48 Manual 0-4825 Rev. AKCartridge Assembly (35-1022) Consumables2x-100535-100735-102335-1022Art # A-09242Shield CupBaf

Página 36

Manual 0-4825 Rev. AK 8-49 TORCH DATA for AutoCut BasicArt # A-06980Torch ClampCoolant ReturnCheck Valve and ConnectorGPositioning TubeREnd CapO-Ring

Página 37 - Auto-Cut 300

TORCH DATA for AutoCut Basic 8-50 Manual 0-4825 Rev. AKArt # A-0725035-103435-105135-106035-106935-1078O-Ring 9-9035O-Ring 9-9035O-Ring 9-903535-1053

Página 38

Manual 0-4825 Rev. AK 8-51 TORCH DATA for AutoCut BasicPATENT INFORMATIONXTXTXTXTXTTMTMTMTMTM-301 Plasma Cutting -301 Plasma Cutting -301 Plasma Cutt

Página 39 - TORCH REPLACEMENT PARTS

TORCH DATA for AutoCut Basic 8-52 Manual 0-4825 Rev. AKXTXTXTXTXTTMTMTMTMTM-301 Plasma Cutting -301 Plasma Cutting -301 Plasma Cutting -301 Plasma Cu

Página 40 - Cartridge Assembly

Manual 0-4825 Rev. AK 8-7 TORCH DATA for AutoCut BasicPlasma (Air) Shield (Air) (ga) (in) inch (PSI) (PSI) Volts(in)±0.005(ipm)(in)(sec)(in)21 0.03

Página 41 - Art # A-06980

TORCH DATA for AutoCut Basic 8-8 Manual 0-4825 Rev. AKAluminum55AAir Plasma / Air ShieldPlasma (Air) Shield (Air) (ga) (in) inch (PSI) (PSI) Volts(

Página 42 - Art # A-07250

Manual 0-4825 Rev. AK 8-9 TORCH DATA for AutoCut BasicMild Steel100AAir Plasma / Air ShieldCartridge35-1020Shield Cup35-1016Shield Cap35-1027Shield G

Página 43

TORCH DATA for AutoCut Basic 8-10 Manual 0-4825 Rev. AKMild Steel100AO2 Plasma / Air ShieldPlasma (O2) Shield (Air) (ga) (in) inch (PSI) (PSI) Volt

Página 44

Manual 0-4825 Rev. AK 8-11 TORCH DATA for AutoCut BasicPlasma (Air) Shield (Air) (ga) (in) inch (PSI) (PSI) Volts(in)±0.005(ipm)(in)(sec)(in)16 0.0

Mais documentos para Hardware Tweco Torch Data AutoCut

Para ver o documento Tweco Torch Data AutoCut Manual do Utilizador

Tweco Torch Data AutoCut Manual do Utilizador (52 páginas)

Comentários a estes Manuais

Sem comentários

Tweco Torch Data AutoCut Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Hardware Tweco Torch Data AutoCut. Tweco Torch Data AutoCut User Manual Manual do Utilizador

Resumo do Conteúdo

Mais documentos para Hardware Tweco Torch Data AutoCut

Comentários a estes Manuais

Manuais e produtos relacionados com Hardware Tweco Torch Data AutoCut